One would think that you do not have to turn on a spinning bike. However, the Peloton is a state-of-the-art piece of exercise equipment, and although it may seem daunting to look at. Turning it on is simple enough.
The proper method of turning on a Peloton which can be found in the Peloton manual is to push and hold the power button located at the back of the monitor for two seconds. This will turn on a Peloton. Make sure it is plugged in and switched on before you do so.
Is there a way to turn a Peloton on correctly? Find out how and discover the problem if it doesn’t by working through our step-by-step tutorial. This article covers all the ins and outs of powering on your Peloton.
How To Turn On A Peloton Bike
The procedure for turning on your Peloton is anything far from complicated and does not require a degree in electrical engineering. If you find yourself unable to turn your Peloton on, then all you need to do is troubleshoot what the problem could be one element at a time. Within a minute or two, your bike will be turned on, and you can cycle to your heart’s content.
If your Peloton is set up correctly, then you only need to push the power on button to switch it on. The Peloton manual that is shipped with every bike tells you how to do this.
- If you are positive everything is plugged in and working correctly, you will need to push and hold the power button located at the back of the Peloton screen for two seconds to power on the bike
If you find that after you push and hold the power button for two seconds your Peloton does not turn on, you will have to go through our troubleshooting tutorial to discover what the problems could be.
Peloton Power Troubleshooting Tutorial
This tutorial will lay out the steps needed to figure out why your Peloton won’t turn on. It will start with you checking the back of the bike and subsequently moving forward to any problem areas.
How To Check The Power Of Your Peloton
The first step you should take is to ensure that everything is alright with your power supply and power cable. The power supply is how the Peloton draws power, and without it, it won’t turn on.
It may seem obvious, but you should make sure that your power supply is plugged into an outlet or power strip and they are turned on.
Take note that you should opt to get a power strip with surge protection if you do not have one because, in the event of a power surge or lightning storm, your Peloton and/or power supply could become damaged, and with it being such an investment it is important to be sure it is protected from the what if’s of life.
Check out this Power Strip on Amazon here
If everything seems fine thus far, the next thing to check is the actual power supply to the bike. Depending on what Peloton power supply you have, there may be a LED situated somewhere and if it is on and working, then that LED will illuminate green. If it does not, then there might be something wrong with either the power supply, the cable running to the outlet or power strip, or the outlet or power strip themselves.
Suppose you feel that the problem lies with your home’s electrical wiring for some reason. In that case, we always recommend calling out a professional instead of trying to resolve those types of situations yourself.
If you think the problem lies with your power supply, then you should opt to purchase a new one. Trying to fix a power supply of this nature is not worth your time and buying a new one is inexpensive, plus it will be brand new, so you can be assured it should work properly.
Check out this Peloton replacement power supply on Amazon here
If you are within warranty it may be best to contact Peloton support to discuss your issue and see if they can send a replacement cord before purchasing an off-market cord. air on the side of caution if you are in warranty and decide to purchase a new cord that is not directly from Peloton as this may void your warranty.
Checking All The Cables On The Peloton
Following the power supply, you will need to check all the connection cables. The power supply does have a cable that runs and plugs into the bottom backside of the bike, so make sure that it’s plugged in and secure.
More often than not, the cause of your Peloton not turning on is the result of a loose power supply cable. Another factor could be that it is faulty, and in that case, you will need to replace it.
Check The Monitor Cable
Next, move onto the monitor cable and make sure that it is plugged in correctly to your Peloton screen. At the back of the Peloton screen, a cover plate needs to be removed to gain access to the cables. To remove the cover plate simply unclick it from the screen using your hands (it is similar to snapping a cell phone cover on and off).
Once it is off, you will notice that the monitor cable has two connection points. Make sure that these are correctly plugged in and that they are in the correct places. If everything looks good, but your bike still does not want to turn on, then there is one last step you can take.
Check The Peloton Resistance Knob And Wiggle The Wires
The Peloton has the wires running from the power supply to the monitor within its chassis. Sometimes (but not very often), the resistance knob and other internal elements can damage or distort the power cable running to your monitor.
What you will need to do is find someone to help you. One of you will adjust the resistance knob and fiddle with it while the other tries to power on the screen. If you find that this works, you will need to call a technician to remedy the problem.
With the help of somebody else, the last thing you can do is check all the cables to see if they are faulty. The same method will apply here. One of you will sequentially navigate from the back of the bike (including the power cord) and wiggle all the cables while the other tries to power on the bike.
If you find that one of the cables is faulty, it will need to be replaced. Depending on which cable it is, you will be able to purchase and replace it yourself unless the bike is still under warranty, or you will need to call out a technician again to help with the problem.
Conclusion
Turning on the Peloton is a pretty simple procedure that anyone can do. All you need to do is hold the power button located on the back of the monitor for two seconds, and it should power on easily.
The only time that it will not turn on is when there is some sort of fault that is either occurring at the power supply, with the cables that run from the power supply to the monitor, or otherwise the monitor itself.
If you have gone through our tutorial and found nothing has worked to turn on your Peloton, the only conclusion we can arrive at is that your actual screen is faulty, and it will need to be tested and checked by a technician.